Air Handlers 216

Overview

Commercial Achiever air handlers feature industry standard R-410A refrigerant, powder coat painted cabinets and plenums, along with inherently protected motors.

Features

• The RHCLP Air Handler is designed for heat pump applications. It has two TX valves with internal check valves that allow reverse flow to occur, providing superior control during heating and cooling cycles. The RHCLP Air Handler has been rated and certified to operate with matching size RPCL heat pumps.
• Horizontal air flow
• 208 / 230 volt, 60 hertz , 3 phase
• Supply dimensions: 19-7/8" x 19-7/8"
• Return dimensions: 47-3/8" x 19-7/8" high
• Two 1/2" liquid line connections or one 5/8" liquid line connection
• Two 7/8" suction line connections or one 1-3/8" suction line connection
• Field piping connections are made through a fixed post between two side access panels on either side of the unit. Allows flexibility to meet most field conditions as well as full accessibility after the installation is complete. Units may be used with two straight cool condensing units or single circuit manifolded in the field using the copper fittings shipped with each unit.
• The pre-painted, sheet metal cabinet uses 18-gauge material for structural components with an underlying coat of G60 electro deposition powder coating that is tested to withstand a rigorous 500 hour salt spray test, per ASTM B117.
• Inherently protected motors are mounted inside of insulated cabinet to reduce motor noise.
• Low profile allows for horizontal installation in most standard drop ceiling applications, and the movement of units through most standard doorways for addition or replacement work.
• Standard thermal expansion valves (TXV)
• One inch throwaway filters are standard, but filter racks are designed to accept either 1" or 2" filters
• Two circuit, interlaced row split coils are constructed with copper tubes and aluminum fins mechanically bonded to the tubes for maximum heat transfer capabilities. All coil assemblies are leak tested up to 450 PSIG [3100 kPa] internal pressure prior to installation into units.
• Variable frequency drive provides 2 stage airflow for improved part load efficiency.
• The galvanized steel drain pan is designed to trap condensate in either vertical or horizontal installations. Condensate drain connections are located on both sides of the unit allowing complete flexibility to meet most field conditions.
• Two removable panels on top and each side of the unit are easily removed for access to motors, blowers, sheaves, and filters.
• Can be installed in horizontal or vertical position

Overview

Commercial Achiever air handlers feature industry standard R-410A refrigerant, powder coat painted cabinets and plenums, along with inherently protected motors.

Features

• Horizontal air flow
• 208 / 230 volt, 60 hertz , 3 phase
• Supply dimensions: 19-7/8" x 19-7/8"
• Return dimensions: 47-3/8" x 19-7/8" high
• Two 1/2" liquid line connections or one 5/8" liquid line connection
• Two 7/8" suction line connections or one 1-3/8" suction line connection
• Field piping connections are made through a fixed post between two side access panels on either side of the unit. Allows flexibility to meet most field conditions as well as full accessibility after the installation is complete. Units may be used with two straight cool condensing units or single circuit manifolded in the field using the copper fittings shipped with each unit.
• The pre-painted, sheet metal cabinet uses 18-gauge material for structural components with an underlying coat of G60 electro deposition powder coating that is tested to withstand a rigorous 500 hour salt spray test, per ASTM B117.
• Inherently protected motors are mounted inside of insulated cabinet to reduce motor noise.
• Low profile allows for horizontal installation in most standard drop ceiling applications, and the movement of units through most standard doorways for addition or replacement work.
• Standard thermal expansion valves (TXV)
• One inch throwaway filters are standard, but filter racks are designed to accept either 1" or 2" filters
• Two circuit, interlaced row split coils are constructed with copper tubes and aluminum fins mechanically bonded to the tubes for maximum heat transfer capabilities. All coil assemblies are leak tested up to 450 PSIG [3100 kPa] internal pressure prior to installation into units.
• Variable frequency drive provides 2 stage airflow for improved part load efficiency.
• The galvanized steel drain pan is designed to trap condensate in either vertical or horizontal installations. Condensate drain connections are located on both sides of the unit allowing complete flexibility to meet most field conditions.
• Two removable panels on top and each side of the unit are easily removed for access to motors, blowers, sheaves, and filters.
• Can be installed in horizontal or vertical position

Overview

Commercial Achiever air handlers feature industry standard R-410A refrigerant, powder coat painted cabinets and plenums, along with inherently protected motors.

Features

• The RHCLP Air Handler is designed for heat pump applications. It has two TX valves with internal check valves that allow reverse flow to occur, providing superior control during heating and cooling cycles. The RHCLP Air Handler has been rated and certified to operate with matching size RPCL heat pumps.
• Horizontal air flow
• 208 / 230 volt, 60 hertz , 3 phase
• Supply dimensions: 19-7/8" x 19-7/8"
• Return dimensions: 47-3/8" x 19-7/8" high
• Two 1/2" liquid line connections or one 1/2" liquid line connection
• Two 7/8" suction line connections or one 1-1/8" suction line connection
• Field piping connections are made through a fixed post between two side access panels on either side of the unit. Allows flexibility to meet most field conditions as well as full accessibility after the installation is complete. Units may be used with two straight cool condensing units or single circuit manifolded in the field using the copper fittings shipped with each unit.
• The pre-painted, sheet metal cabinet uses 18-gauge material for structural components with an underlying coat of G60 electro deposition powder coating that is tested to withstand a rigorous 500 hour salt spray test, per ASTM B117.
• Inherently protected motors are mounted inside of insulated cabinet to reduce motor noise.
• Low profile allows for horizontal installation in most standard drop ceiling applications, and the movement of units through most standard doorways for addition or replacement work.
• Standard thermal expansion valves (TXV)
• One inch throwaway filters are standard, but filter racks are designed to accept either 1" or 2" filters
• Two circuit, interlaced row split coils are constructed with copper tubes and aluminum fins mechanically bonded to the tubes for maximum heat transfer capabilities. All coil assemblies are leak tested up to 450 PSIG [3100 kPa] internal pressure prior to installation into units.
• Variable frequency drive provides 2 stage airflow for improved part load efficiency.
• The galvanized steel drain pan is designed to trap condensate in either vertical or horizontal installations. Condensate drain connections are located on both sides of the unit allowing complete flexibility to meet most field conditions.
• Two removable panels on top and each side of the unit are easily removed for access to motors, blowers, sheaves, and filters.
• Can be installed in horizontal or vertical position

Overview

The Ruud RH2TZ Air Handler provides enduring comfort and energy savings. It's sturdy design, quiet operation and humidity control features enhance the air quality in your home, delivering comfort you can count on

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 10-5/16 inches front to back - 23 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 22-7/8 inches side to side
• For use with air conditioners or heat pumps
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg motor mount
• Constant torque ECM blower moter
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer corrosion resistant condensate drain pan
• Coils have sweat refrigerant connections
• Coils utilize chatleff metering device connections
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Side or top provisions for electrical connections
• Front refrigerant and drain connections

Overview

The Weatherking WH1P Air handler is designed with a sturdy steel cabinet with one inch of foil faced insulation, offering excellent thermal and sound insulation, which means you get quiet and efficient comfort. The WH1P Air Handler adjusts airflow in the home to help control humidity. Airflow can be set for specific needs so your home feels just the way you want it. The factory installed indoor aluminum cooling coil is the key component for your air handler. The coil is essential to humidity control and improved system performance. The new lanced fin design also provides maximum performance and increased efficiency. The high grade condensate drain pan keeps the unit operating smoothly and the corrosion resistant aluminum endplates keep the unit looking as good as it runs.

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 10-5/16 inches front to back - 16 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 15-7/8 inches side to side
• Can be used with air conditioners
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg motor mount
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer corrosion resistant condensate drain pan
• Expansion valve on indoor coil provides for operation with air conditioning
• Coils have sweat refrigerant connections
• Coils utilize chatleff metering device connections
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Front refrigerant and drain connections

Overview

The Weatherking WH1P Air handler is designed with a sturdy steel cabinet with one inch of foil faced insulation, offering excellent thermal and sound insulation, which means you get quiet and efficient comfort. The WH1P Air Handler adjusts airflow in the home to help control humidity. Airflow can be set for specific needs so your home feels just the way you want it. The factory installed indoor aluminum cooling coil is the key component for your air handler. The coil is essential to humidity control and improved system performance. The new lanced fin design also provides maximum performance and increased efficiency. The high grade condensate drain pan keeps the unit operating smoothly and the corrosion resistant aluminum endplates keep the unit looking as good as it runs.

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 10-5/16 inches front to back - 16 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 15-7/8 inches side to side
• Can be used with air conditioners
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg motor mount
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer corrosion resistant condensate drain pan
• Expansion valve on indoor coil provides for operation with air conditioning
• Coils have sweat refrigerant connections
• Coils utilize chatleff metering device connections
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Front refrigerant and drain connections

Overview

Ruud High Efficiency air handlers featuring industry standard R-410A refrigerant now also come with GE's new X-13 motor, which provides enhanced SEER performance with most Ruud outdoor units.

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 18 inches front to back - 9-7/16 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 20 inches side to side - Return duct flanges are standard
• Can be used with air conditioners
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg rubber insulated wire motor mount
• Slide out blower housing with motor, blower, heaters and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to tinned copper tubing
• Molded polymer corrosion resistant condensate drain pan
• High voltage and low voltage connections are on the inside of the cabinet with provisions for connections on each side
• Front refrigerant and drain connections
• Circuit breaker is included with this unit
• Durable framed, cleanable air filter provided as standard in the unit filter rack

Overview

The Ruud RHGM Commercial heat pump air handler includes an inherently protected motor mounted inside the insulated cabinet, field piping connections made through a fixed post between two side access panels, and may be installed in horizontal or vertical applications.

Features

• This is a multiposition heat pump air handler: Vertical or horizontal
• Inherently protected motor is mounted inside the insulated cabinet to reduce motor noise
• Low profile allows for horizontal installation and allows the unit to be moved through most standard doorways
• Two thermal expansion valves with internal check valves
• One inch throwaway filters are standard, but the filter racks are designed to accept either one inch or two inch filters
• Two circuit, interlaced row split coils are constructed with copper tubing and aluminum fins mechanically bonded to the tubing
• Refrigerant connections are made through a fixed post located between two side access panels on either side of the unit.
• The galvanized steel drain pan is designed to trap condensate in either vertical or horizontal installations
• Two removable panels on top and each side of the unit are easily removed for access to motors, blowers, sheaves and filters

Overview

The Ruud RHMV EcoNet enabled air handler is equipped with an electronic expansion valve (EEV), which can intelligently change the EEV position based on system demands. By the measurement of the suction pressure via the vapor line pressure transducer (factory installed) and the vapor line thermistor (field connected to the vapor line, but factory provided within the air handler) the EcoNet enabled air handler control calculates the suction superheat at the indoor coil. This calculation permits the air handler control to make decisions for when to open and close the EEV for the purpose of maintaining a predetermined suction superheat. The EEV is equipped with a 4 pole removable external stator, and inlet and outlet chatleff fittings for optimal serviceability. These valves also have an internal check valve to provide heat pump compatibility. When operating in heating mode, the air handler control will open the EEV completely to permit the check valve to operate and maximize reverse refrigerant flow.

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Can be used with air conditioning or heat pumps
• Modulating air flow
• Supply dimensions: 10-5/16 inches front to back - 19-1/2 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 19-3/8 inches side to side
• EcoNet controls
• The most compact unit design available
• Pre-painted rugged steel cabinet
• 1 inch foil faced insulation mechanically retained in blower cabinet
• Four leg blower motor
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Top, left or right side electrical connections
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer, corrosion resistant condensate drain pan
• Coils utilize chatleff metering devices
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Front refrigerant and drain connections

Overview

The Ruud RW1T hydronic air handler with an ECM motor, features a hydronic heating coil in place of either electric heating elements or gas fired heat exchangers. When in heating mode, the hydro pump circulates hot water between the tankless water heater (not included) or boiler (not included) and the hydronic coil.

Features

• This unit does not include an air conditioning coil - If air conditioning is required, a 3 ton cased coil must be purchased separately
• 60,000 BTU heating capacity
• This is a multiposition air handler shipped as an upflow unit, but convertible to downflow, horizontal right or horizontal left
• Supply dimensions: 20 inches front to back - 16-1/2 inches side to side - Supply duct flanges are standard
• Return dimensions: 20 inches front to back - 16-1/2 inches side to side
• Low profile design is lighter and easier to handle while also leaving room for an optional cased coil
• Pre-painted galvanized steel cabinet
• Insulated blower compartment
• Integrated control board features diagnostics and manages all operational functions while providing hookups for a humidifier and an electronic air cleaner
• Left or right side electrical connections
• Molded, permanent air filter
• Transformer and control fuse protection
• Standard solid bottom
• Stainless steel circulator pump
• Front 3/4 inch sweat inlet and outlet water connections

Overview

Ruud High Efficiency air handlers featuring industry standard R-410A refrigerant and energy efficient GE ECM motor for quiet operation and enhanced customer satisfaction

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left - Vertical upflow / horizontal left is the factory configuration
• Supply dimensions: 10-5/16 inches front to back - 23 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-1/2 inches front to back - 22-7/8 inches side to side
• Can be used with air conditioners or heat pumps
• Interface board with dip switches conveniently located in the blower compartment allows precise, field selectable airflow
• Quiet, efficient ECM motor
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg blower motor mount
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved copper tubing
• Molded polymer corrosion resistant condensate drain pan
• Provisions for field electrical connections are on both sides or the top of the cabinet
• High voltage wiring connection is inside the cabinet - Low voltage connection is on the outside of the cabinet
• Front refrigerant and drain connections

[* 2 TON - PSC - W/ A2L SENSOR]

[* FOR RH2TZ4821STANNJ AIR HANDLER]

[* 31/2 TON - 15 SEER2 - R454B - SINGLE STAGE]

[* 21/2 & 3 TON - 2 STAGE - CONSTANT TORQUE]

[* 2.5 & 3 TON R-410A 2STAGE CONSTANT TORQUE]

[* FRONT RETURN AIR HANDLER]

[* 115V - 2 STAGE - CONSTANT TORQUE]

* 115V - 3.5 / 4 TON - 35"H x 24'W

Overview

The Weatherking WH1PZ Air handler is designed with a sturdy steel cabinet with one inch of foil faced insulation, offering excellent thermal and sound insulation, which means you get quiet and efficient comfort. The WH1PZ Air Handler adjusts airflow in the home to help control humidity. The factory installed indoor aluminum cooling coil is the key component for your air handler. The coil is essential to humidity control and improved system performance. The high grade condensate drain pan keeps the unit operating smoothly

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 18 inches front to back - 19-1/2 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 19-3/8 inches side to side - Return duct flanges are standard
• Can be used with air conditioners
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg motor mount
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer corrosion resistant condensate drain pan
• Expansion valve on indoor coil provides for operation with air conditioning
• Coils have sweat refrigerant connections
• Coils utilize chatleff metering device connections
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Electrical connections can be made from the left side, right side or top of the cabinet
• Front refrigerant and drain connections

Overview

The Weatherking WH1PZ Air handler is designed with a sturdy steel cabinet with one inch of foil faced insulation, offering excellent thermal and sound insulation, which means you get quiet and efficient comfort. The WH1PZ Air Handler adjusts airflow in the home to help control humidity. The factory installed indoor aluminum cooling coil is the key component for your air handler. The coil is essential to humidity control and improved system performance. The high grade condensate drain pan keeps the unit operating smoothly

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 18 inches front to back - 16 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 15-7/8 inches side to side - Return duct flanges are standard
• Can be used with air conditioners
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg motor mount
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer corrosion resistant condensate drain pan
• Expansion valve on indoor coil provides for operation with air conditioning
• Coils have sweat refrigerant connections
• Coils utilize chatleff metering device connections
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Electrical connections can be made from the left side, right side or top of the cabinet
• Front refrigerant and drain connections

Overview

The Weatherking WH1PZ Air handler is designed with a sturdy steel cabinet with one inch of foil faced insulation, offering excellent thermal and sound insulation, which means you get quiet and efficient comfort. The WH1PZ Air Handler adjusts airflow in the home to help control humidity. The factory installed indoor aluminum cooling coil is the key component for your air handler. The coil is essential to humidity control and improved system performance. The high grade condensate drain pan keeps the unit operating smoothly

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 18 inches front to back - 16 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 15-7/8 inches side to side - Return duct flanges are standard
• Can be used with air conditioners
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg motor mount
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer corrosion resistant condensate drain pan
• Expansion valve on indoor coil provides for operation with air conditioning
• Coils have sweat refrigerant connections
• Coils utilize chatleff metering device connections
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Electrical connections can be made from the left side, right side or top of the cabinet
• Front refrigerant and drain connections

Overview

The Weatherking WH1PZ Air handler is designed with a sturdy steel cabinet with one inch of foil faced insulation, offering excellent thermal and sound insulation, which means you get quiet and efficient comfort. The WH1PZ Air Handler adjusts airflow in the home to help control humidity. The factory installed indoor aluminum cooling coil is the key component for your air handler. The coil is essential to humidity control and improved system performance. The high grade condensate drain pan keeps the unit operating smoothly

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 18 inches front to back - 16 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 15-7/8 inches side to side - Return duct flanges are standard
• Can be used with air conditioners
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg motor mount
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer corrosion resistant condensate drain pan
• Expansion valve on indoor coil provides for operation with air conditioning
• Coils have sweat refrigerant connections
• Coils utilize chatleff metering device connections
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Electrical connections can be made from the left side, right side or top of the cabinet
• Front refrigerant and drain connections

Overview

The Weatherking WH1PZ Air handler is designed with a sturdy steel cabinet with one inch of foil faced insulation, offering excellent thermal and sound insulation, which means you get quiet and efficient comfort. The WH1PZ Air Handler adjusts airflow in the home to help control humidity. The factory installed indoor aluminum cooling coil is the key component for your air handler. The coil is essential to humidity control and improved system performance. The high grade condensate drain pan keeps the unit operating smoothly

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 18 inches front to back - 16 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 15-7/8 inches side to side - Return duct flanges are standard
• Can be used with air conditioners
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg motor mount
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer corrosion resistant condensate drain pan
• Expansion valve on indoor coil provides for operation with air conditioning
• Coils have sweat refrigerant connections
• Coils utilize chatleff metering device connections
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Electrical connections can be made from the left side, right side or top of the cabinet
• Front refrigerant and drain connections

Overview

The Weatherking WH1PZ Air handler is designed with a sturdy steel cabinet with one inch of foil faced insulation, offering excellent thermal and sound insulation, which means you get quiet and efficient comfort. The WH1PZ Air Handler adjusts airflow in the home to help control humidity. The factory installed indoor aluminum cooling coil is the key component for your air handler. The coil is essential to humidity control and improved system performance. The high grade condensate drain pan keeps the unit operating smoothly

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 18 inches front to back - 16 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 15-7/8 inches side to side - Return duct flanges are standard
• Can be used with air conditioners
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg motor mount
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer corrosion resistant condensate drain pan
• Expansion valve on indoor coil provides for operation with air conditioning
• Coils have sweat refrigerant connections
• Coils utilize chatleff metering device connections
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Electrical connections can be made from the left side, right side or top of the cabinet
• Front refrigerant and drain connections

Overview

The Weatherking WH1PZ Air handler is designed with a sturdy steel cabinet with one inch of foil faced insulation, offering excellent thermal and sound insulation, which means you get quiet and efficient comfort. The WH1PZ Air Handler adjusts airflow in the home to help control humidity. The factory installed indoor aluminum cooling coil is the key component for your air handler. The coil is essential to humidity control and improved system performance. The high grade condensate drain pan keeps the unit operating smoothly

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 18 inches front to back - 23 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 22-7/8 inches side to side - Return duct flanges are standard
• Can be used with air conditioners
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg motor mount
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer corrosion resistant condensate drain pan
• Expansion valve on indoor coil provides for operation with air conditioning
• Coils have sweat refrigerant connections
• Coils utilize chatleff metering device connections
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Electrical connections can be made from the left side, right side or top of the cabinet
• Front refrigerant and drain connections

Overview

The Weatherking WH1PZ Air handler is designed with a sturdy steel cabinet with one inch of foil faced insulation, offering excellent thermal and sound insulation, which means you get quiet and efficient comfort. The WH1PZ Air Handler adjusts airflow in the home to help control humidity. The factory installed indoor aluminum cooling coil is the key component for your air handler. The coil is essential to humidity control and improved system performance. The high grade condensate drain pan keeps the unit operating smoothly

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 18 inches front to back - 16 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 15-7/8 inches side to side - Return duct flanges are standard
• Can be used with air conditioners
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg motor mount
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer corrosion resistant condensate drain pan
• Expansion valve on indoor coil provides for operation with air conditioning
• Coils have sweat refrigerant connections
• Coils utilize chatleff metering device connections
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Electrical connections can be made from the left side, right side or top of the cabinet
• Front refrigerant and drain connections

Overview

The Weatherking WH1PZ Air handler is designed with a sturdy steel cabinet with one inch of foil faced insulation, offering excellent thermal and sound insulation, which means you get quiet and efficient comfort. The WH1PZ Air Handler adjusts airflow in the home to help control humidity. The factory installed indoor aluminum cooling coil is the key component for your air handler. The coil is essential to humidity control and improved system performance. The high grade condensate drain pan keeps the unit operating smoothly

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 18 inches front to back - 16 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 15-7/8 inches side to side - Return duct flanges are standard
• Can be used with air conditioners
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg motor mount
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer corrosion resistant condensate drain pan
• Expansion valve on indoor coil provides for operation with air conditioning
• Coils have sweat refrigerant connections
• Coils utilize chatleff metering device connections
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Electrical connections can be made from the left side, right side or top of the cabinet
• Front refrigerant and drain connections

Overview

The Weatherking WH1PZ Air handler is designed with a sturdy steel cabinet with one inch of foil faced insulation, offering excellent thermal and sound insulation, which means you get quiet and efficient comfort. The WH1PZ Air Handler adjusts airflow in the home to help control humidity. The factory installed indoor aluminum cooling coil is the key component for your air handler. The coil is essential to humidity control and improved system performance. The high grade condensate drain pan keeps the unit operating smoothly

Features

• This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
• Supply dimensions: 18 inches front to back - 19-1/2 inches side to side - Supply duct flanges are standard
• Return dimensions: 19-3/4 inches front to back - 19-3/8 inches side to side - Return duct flanges are standard
• Can be used with air conditioners
• The most compact unit design available
• Attractive, rugged steel wall cabinet with pre-painted exterior
• 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
• Four leg motor mount
• Slide out blower housing with motor, blower and controls for service and maintenance convenience
• Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
• Molded polymer corrosion resistant condensate drain pan
• Expansion valve on indoor coil provides for operation with air conditioning
• Coils have sweat refrigerant connections
• Coils utilize chatleff metering device connections
• High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
• Electrical connections can be made from the left side, right side or top of the cabinet
• Front refrigerant and drain connections