The Taco Hy-Vent has become the industry standard for dependable long life service. The high capacity float style vents can be placed
either on the boiler or at the high points throughout the system. Now with operating pressure ratings of up to 250 PSI, the brass body, nickel
plated vents meet the system requirements of even the largest installation. The vents are also easily serviceable if needed, by just
unscrewing the vent cap.
The Taco Hy-Vent has become the industry standard for dependable long life service. The high capacity float style vents can be placed
either on the boiler or at the high points throughout the system. Now with operating pressure ratings of up to 150 PSI, the brass body, nickel
plated vents meet the system requirements of even the largest installation. The vents are also easily serviceable if needed, by just
unscrewing the vent cap.
Brass body - 150 PSI maximum working pressure - 40 PSI maximum discharge pressure - 1.75 SCFM maximum discharge rate - 230 degrees
maximum working temperature
Chrome plated brass body - Automatic operation - Can be operated manually by rotating knob - For hydronic heating systems or low
pressure steam - 150 PSI maximum working pressure - 212 degrees maximum working temperature - 15 PSI maximum steam pressure
For solar fluid - Brass chrome plated body - 150 PSI maximum working pressure - 75 PSI maximum discharge pressure - Minus 20 to 360 degrees
working temperature range
Brass body and cover with stainless steel internal components - 3/8 inch FIPS top discharge - 230 PSI maximum working pressure - 90
PSI maximum discharge pressure - 9 SCFM maximum discharge rate - Minus 4 to 250 degrees working temperature range
Brass body - 150 PSI maximum working pressure - 60 PSI maximum discharge pressure - 2.5 SCFM maximum discharge rate - 250 degrees
maximum working temperature
Installed on water or stream radiators the Taco automatic coin vent is the ideal air purging device. The coin vent features special
hygroscopic cellulose discs in the valve body. When dry the discs allow air to be released from the system. Once all the air is purged
the discs would then come in contact with system water, where upon they would swell to create a positive shut-off. This continuous
cycle prevents the radiators from becoming air bound and speeds the process of filling the system. The vent can also be manually
shut off by means of an internal ball check. The 417 coin vent is suitable for use in water and low pressure steam applications.
Brass body - 150 PSI maximum working pressure - 90 PSI maximum discharge pressure - 1.75 SCFM maximum discharge rate - 240 degrees
maximum working temperature
Brass body - 150 PSI maximum working pressure - 40 PSI maximum discharge pressure - 1.75 SCFM maximum discharge rate - 230 degrees
maximum working temperature
This 1/8 inch high capacity air vent includes a manual vent feature and is used in commercial and residential hydronic heating applications to provide automatic
air venting for hot or cold water distribution systems. It consists of a brass body construction with female NPT connection, brass cover, air vent with silicone rubber
seal, shutter, polyethylene float with valve plug, automatic vent with black cap, and manual vent with red cap. It has a high capacity and high temperature rating and
is ideal for use with glycol systems or for use as an anti-vacuum device. It can be disassembled for inspection and cleaning. The maximum pressure is 150 psi
Patented SWG or ComboVent Power Venters are ETL and cETL listed for all LP gas, natural gas, or oil-fired heating equipment. The SWG or ComboVent combines the motor, blower, and vent hood in one complete, easy to install unit. The SWG mounts on the outside of the building and pulls the combustion gases from the appliance through the outside wall utilizing 100% negative pressure.
Features
100% negative pressure in the vent pipe for maximum safety.
Standard galvanized pipe can be used instead of expensive stainless steel.
No need to seal vent pipe joints, saving time and money.
Significantly longer vent lengths than positive pressure, direct vent systems.
The SWG or ComboVent is recommended by major heating appliance manufacturers.
The Taco Hy-Vent has become the industry standard for dependable long life service. The high capacity float style vents can be placed
either on the boiler or at the high points throughout the system. Now with operating pressure ratings of up to 150 PSI, the brass body, nickel
plated vents meet the system requirements of even the largest installation. The vents are also easily serviceable if needed, by just
unscrewing the vent cap.
This 1/8 inch automatic air vent valve is used in commercial and residential hydronic heating applications to provide automatic air
venting for hot or cold water distribution systems. It consists of a brass body construction with male NPT connection, brass cover,
air vent with silicone rubber seal, polyethylene float with valve plug, and automatic vent. It has a high temperature rating and is ideal for
use with glycol systems or for use as an anti-vacuum device. It can also be installed to permit the separation and dispersal of air while
fluid is circulating in the system. It can be disassembled for inspection and cleaning. The maximum pressure is 150 psi
The Taco 409 air vent is a heavy duty brass vent rated to 150 psi system operating pressure. The conical shapeof the vent significantly
increases the clearance between the water level and internal mechanisms, reducing the potential that dirt floating on the top of the water
could foul the venting operation. It features a convenient outlet connection for a 3/4 ID flex tube waste connection. It’s high capacity
design makes it ideal for placement throughout commercial systems
