Upflow or horizontal - Supply air 19 inches front to back and 18 inches wide - Return air 21-1/2 inches front to back and 16 inches wide - Factory installed coil - Convertible horizontal drain pan - 20 inch x 22 inch x 1 inch filter - 58,900 heating BTU - 7/8 OD hot water coil connection - Multi- function microprocessor circuit board - Blower Start Relay allows direct wiring from the boiler to the air handler - Blower on fan delay preheats the hot water coil for 45 seconds - Blower off fan delay allows the blower to operate for 45 seconds after the thermostat is satisfied - The microprocessor powers either 120 volt or 24 volt motorized zone valves (not included) - Factory installed R410A TXV valve - Manual air vent on hot water coil - Blower door shut off switch - Slide out hot water coil for easier service - Copper tube heating and cooling coils - Compatible with all major brands of split condensing units and heat pumps - Attractive baked on powder coated cabinet - Primary and secondary condensate drain connections - Easily accessible air filter
Air Handlers 216
Overview
Fujitsu Airstage VR-II sytems offer simultaneous cooling and heating operation from one refrigerant system by using variable refrigerant flow (VRF) technology. The Airstage VR-II system has a much lower life cycle cost due to the great energy efficiency, high quality and features such as easy to design, install and maintain. The Airstage VR-II systems are always comfortable because the advanced controls react quickly to demand changes to always keep the climate comfortable. Airstage heat recovery systems offer efficient climate control by extracting heat from rooms or zones that require cooling, and transferring the heat to other rooms or zones that, at the same time, require heating. This creates maximum comfort in all areas while optimizing energy efficiency.
Features
- Three position: Upflow, horizontal right or horizontal left
- 2 ton cooling capacity - 27,000 BTU's heating capacity
- Three speed fan: 650 CFM, 590 CFM and 510 CFM
- One Sirocco fan
- Easy access front panel
- 16 inch x 20 inch x 1 inch filter
- Auxilliary heat operation capability (Auxilliary heat not included)
208/230V - UP TO 5 TONS - 24" WIDE
******APEX TUD48-60AHCADU 4/5 TON INDOOR AH 24" WIDE
FAN MOTOR: HP 1 - FLA (A) 3.2
AIRFLOW: 5-TON = 1600 - 4-TON 1470
SOUND LEVEL dN(A): 5-TON = 51 - 4-TON = 50 - DEHUMIDICATION (PT/HR): 7
POWER SUPPLY: 208/230V-1PH-60HZ - VOLTAGE RANGE: 187 ~ 253
MCA (A): 4 - MOCP/BREAKER: 15 AMP
******APEX TUD48-60WADU 4/5 TON OUTDOOR HP
COMPRESSOR: DC INVERTER DRIVEN ROTARY - RLA (A) 19
REFRIGERANT: R410A
FAN MOTOR: HP 1/5x2 - FLA (A) 1.5x2
CRANKCASE HEATER (W): 40 - SOUND LEVEL dB(A): 58
POWER SUPPLY: 208/230V-1PH-60HZ - VOLTAGE RANGE (V): 187 ~ 253
MCA (A): 35 - MOCP/BREAKER: 45 AMP
******SYSTEM RATING: 5 TON - AHRI# 205984664
COOLING CAPACITY: 54,000 BTU/H - CAPACITY RANGE: 35,000 ~ 54,000 BTU/H
POWER INPUT (W): 5140 - SEER: 17 - EER: 10.5
HEATING CAPACITY: 54,000 BTU/H - CAPACITY RANGE: 35,000 ~ 60,000 BTU/H
POWER INPUT (W): 4590 - HSPF: 10 - COP: 3.45 @ 47F
*** NEXT PAGE ***
HEATING CAPACITY: 38,000 BTU/H - POWER INPUT (W): 4230 - COP: 2.63 @ 17F
******SYSTEM RATING: 4 TON - AHRI# 205993850
COOLING CAPACITY: 48,000 BTU/H - CAPACITY RANGE: 34,000 ~ 48,000 BTU/H
POWER INPUT (W): 4360 - SEER: 18 - EER: 11
HEATING CAPACITY: 48,000 BTU/H - CAPACITY RANGE: 34,000 ~ 52,000 BTU/H
POWER INPUT (W): 3910 - HSPF: 10.5 - COP: 3.6 @ 47F
HEATING CAPACITY: 33,000 BTU/H - POWER INPUT (W): 3810 - COP: 2.54 @ 17F
----------------------------------------------------------------------------
OPERATING RANGE: COOLING: MAX. 129F MIN. 5F - HEATING: MAX. 75F MIN. -22F
PIPING DATA: 3/4" x 3/8" FLARED CONNECTION - FACTORY CHARGE (OZ): 220.8
ADDITIONAL CHARGE (OZ/FT): 0.3 - FACTORY CHARGE LENGTH: 25'
MAX. PIPE LENGTH: 98' - MIN. PIPE LENGTH: 10' - MAX. PIPE ELEVATION: 49'
***FEATURES: SIDE DISCHARGE OUTDOOR UNIT, ZERO LOT LINE DESIGN, MATCH
W/GREE OR COMPETITIVE INDOOR UNIT, DESIGN FOR NEW CONSTRUCTION OR
REPLACEMENT MARKET, QUIET OUTDOOR OPERATION, 24VAC THERMOSTAT COMPATIBLE,
ACRYLIC RESIN/ANTI-CORROSION FIN COATING
***WARRANTY: 10-YEAR LIMITED COMPRESSOR & PARTS (RESIDENTAIL ONLY)
(REGISTRATION NOT REQUIRED)
*** NEXT PAGE ***
DIMENSIONS: (HxWxD) IDU= 57-1/4" x 24-3/4" x 21-1/4" - WEIGHT: 202.8 LBS
ODU= 53-3/4" x 42-3/4" x 15-1/2" - WEIGHT: 308.6 LBS
SUPPLY OPENING: (HxW) 11-5/8" x 20"
NOTES: POWER WIRING SIZE MUST COMPLY W/APPLICABLE NATIONAL & LOCAL CODES
FOR BOTH ID & OD DEDICATED CIRCUITS
TEST CONDITIONS ARE BASED ON AHRI 210/240
***REVISED 09/13/22 NSOARES
Features
- Gloss enameled steel cabinet
- External access to heater circuit breakers, 1 piece design
- Filter rack with magnectic tabs for easy access and removal
- Antimicrobial polymer drain pan, 2% or less air leakage
- Corrosion resistant aluminum alloy fin and tube coil
- Factory leak tested and pre-charged with nitrogen
- ECM variable speed motor, factory installed EXV
Features
- Gloss enameled steel cabinet
- External access to heater circuit breakers, 1 piece design
- Filter rack with magnectic tabs for easy access and removal
- Antimicrobial polymer drain pan, 2% or less air leakage
- Corrosion resistant aluminum alloy fin and tube coil
- Factory leak tested and pre-charged with nitrogen
- ECM variable speed motor, factory installed EXV
[* 5 TON - R410A TXV - CONSTANT TORQUE]
Supply air 11 inches front to back and 16 inches wide - Factory installed coil - 16 inch x 20 inch x 1 inch filter - 45,600 heating BTU - 7/8 OD hot water coil connection - 120 volt motor - Copper tube and aluminum fin heating and cooling coils - Easily accessible air filter - Flue gas door switch - Includes circulator
Features
- Gloss enameled steel cabinet
- External access to heater circuit breakers, 1 piece design
- Filter rack with magnectic tabs for easy access and removal
- Antimicrobial polymer drain pan, 2% or less air leakage
- Corrosion resistant aluminum alloy fin and tube coil
- Factory leak tested and pre-charged with nitrogen
- ECM variable speed motor, factory installed EXV
Overview
Features
- Gloss enameled steel cabinet
- External access to heater circuit breakers, 1 piece design
- Filter rack with magnectic tabs for easy access and removal
- Antimicrobial polymer drain pan, 2% or less air leakage
- Corrosion resistant aluminum alloy fin and tube coil
- Factory leak tested and pre-charged with nitrogen
- ECM variable speed motor, factory installed EXV
[* 1.5/2 TON - R454B - CONSTANT TORQUE]
Overview
Fujitsu Airstage VR-II sytems offer simultaneous cooling and heating operation from one refrigerant system by using variable refrigerant flow (VRF) technology. The Airstage VR-II system has a much lower life cycle cost due to the great energy efficiency, high quality and features such as easy to design, install and maintain. The Airstage VR-II systems are always comfortable because the advanced controls react quickly to demand changes to always keep the climate comfortable. Airstage heat recovery systems offer efficient climate control by extracting heat from rooms or zones that require cooling, and transferring the heat to other rooms or zones that, at the same time, require heating. This creates maximum comfort in all areas while optimizing energy efficiency.
Features
- Three position: Upflow, horizontal right or horizontal left
- 3 ton cooling capacity - 40,000 BTU's heating capacity
- Three speed fan: 1,050 CFM, 950 CFM and 850 CFM
- One Sirocco fan
- Easy access front panel
- 20 inch x 20 inch x 1 inch filter
- Auxilliary heat operation capability (Auxilliary heat not included)
Overview
The Ruud RH2TZ Air Handler provides enduring comfort and energy savings. It's sturdy design, quiet operation and humidity control features enhance the air quality in your home, delivering comfort you can count on
Features
- This is a multiposition air handler: Upflow, downflow, horizontal right or horizontal left
- Supply dimensions: 10-5/16 inches front to back - 19-1/2 inches side to side - Supply duct flanges are standard
- Return dimensions: 19-3/4 inches front to back - 19-3/8 inches side to side
- For use with air conditioners or heat pumps
- The most compact unit design available
- Attractive, rugged steel wall cabinet with pre-painted exterior
- 1 inch of foil faced insulation mechanically retained in blower compartment for excellent thermal and sound performance
- Four leg motor mount
- Constant torque ECM blower moter
- Slide out blower housing with motor, blower and controls for service and maintenance convenience
- Coils are constructed of aluminum fins bonded to internally grooved aluminum tubing
- Molded polymer corrosion resistant condensate drain pan
- Coils have sweat refrigerant connections
- Coils utilize chatleff metering device connections
- High voltage connections are on the inside of the cabinet - Low voltage connections are on the outside of the cabinet
- Side or top provisions for electrical connections
- Front refrigerant and drain connections