The circulator is designed for a wide range of residential and light commercial higher-head circulating applications. Typical uses include hydronic heating, radiant in-floor/panel heating and closed-loop solar heating systems, and domestic water recirculation. The unique replaceable cartridge contains all of the moving parts and allows for easy service, instead of replacing the entire circulator. Compact, direct-drive, low power consumption design is ideal for high-efficiency jobs. Self lubricating - No mechanical seal - Universal flange dimensions
Circulator Pumps 108
The Plumb n Plug periodically re-circulates hot water through the domestic piping system to decrease the delivery time to outlet fixtures and reduce wasted water. Typical timer programming will cycle the Plumb n Plug during high peak usage periods such as early morning or early evening. The 006 PNP is designed for systems using 200 to 400 feet of 3/4 tubing. Installation of isolation valves, pipe insulation and flow checks are recommended.
The 005 is designed for hydronic heating and cooling, Hydro-Air Fan Coils, Radiant heating. The 005-IFC is designed to simplify piping reduce installation costs and improve system performance when zoning with 00 circulators. By locating the IFC inside the pump, a separate in-line flow check is eliminated. The low pressure drop of the IFC increases flow performance vs. in-line flow checks. Both the IFC and the cartridge are easily accessed for removal and service.
The Plumb n Plug periodically re-circulates hot water through the domestic piping system to decrease the delivery time to outlet fixtures and reduce wasted water. Typical timer programming will cycle the Plumb n Plug during high peak usage periods such as early morning or early evening. The Plumb n Plug with Digital Timer allows ON/OFF program settings to fit any homeowners schedule. Multiple settings allow for different weekday/weekend run times. Run time intervals can be set as short as 1 minute to maximize energy savings. Easy-to-Use clock face and large LCD display make settings a snap. Its on-board capacitor retains settings in memory for up to 2,500 hours, during power outages
The Taco 003 is designed for circulating hot or chilled fresh water in open or closed loop, lower flow applications. Flow characteristics are ideal for domestic hot water recirculation, heat recovery units, water source heat pumps and pota-ble water systems. The unique, replaceable cartridge contains all of the moving parts and allows for easy service instead of replacing the entire circulator. The compact, low power consumption design is ideal for high efficiency jobs.
The 0010 3-Speed Service pump is designed as an ideal replacement circulator for service contractors to use on any emergency no heat call. The 0010 3-Speed replaces most commonly used circulators. Simply install it and set the speed to match the original pump performance. The handy new four bolt flange matches up to any pump regardless of style, type or age. Self lubricating - No mechanical seal
The Taco Priority Zoning Circulator combines the reliability of the 00 circulator with the convenience and efficiency of a PC board mounted switching
relay package. Each zoning circulator has low and high voltage terminal strips for ease of electrical hookup, as well as a built-in priority switch. The
priority switch allows the installer to choose the zone that requires the most attention and, when activated, run only that circulator. The priority
zoning circulator can be used in conjunction with other circulators or zone valves. It is ideal for adding another zone, zoning with circulators, and for
prioritizing under-sized zones.
The 1600 Series has a maximum operating pressure of 175 psi, and a maximum operating temperature of 300 F. Replaceable "cooler running" bearing cartridge extends bearing life, and with permanently sealed greased lubricated ball bearings it is virtually maintenance free. Pressure tappings allow for differential pressure readings to be taken across the pump. Dynamically balanced stainless steel impeller assures long life and higher pump efficiencies. Non corrosive shaft sleeve protects the shaft by preventing contact between the shaft and system fluid eliminating the need for more expensive corrosion resistant shaft materials. 1600 Series In-Line pumps utilize a Type 21 seal design which facilitates quick and easy replacement. One size seal fits all models. Flexible coupler absorbs shock, vibration and misalignment that could be transmitted to the cartridge and motor bearings while also isolating and preventing any motor related noise or vibrations from being transmitted to the system. Resilient mounted motor insures quiet reliable vibration free operation of the pump. Superior parts flexibility: one cartridge, one seal, and two motor frames fit all pump models. All 1600 series pumps are factory tested, and are built in accordance with Hydraulic Institute Standards.
Compact, space saving design - Powerful close-coupled, maintenance free motor - Superior efficiency, high starting torque - Permanently lubricated, sealed for life bearings - Rugged 1/2" Stainless Steel Shaft - Carbon/Silicon-Carbide mechanical seal for long life - Universal flange to flange dimensions; Ideal for retrofits - Anti-Condensate design for chilled water - Dual electrical knock-outs - Dual pressure taps, suction and discharge
The circulator is designed for a wide range of residential and light commercial higher-head circulating applications. Typical uses include hydronic heating, radiant in-floor/panel heating and closed-loop solar heating systems, and domestic water recirculation. The unique replaceable cartridge contains all of the moving parts and allows for easy service, instead of replacing the entire circulator. Compact, direct-drive, low power consumption design is ideal for high-efficiency jobs. Self lubricating - No mechanical seal - Universal flange dimensions
Resilient mounted, split phase motor with built-in overload protector - Equipped with sleeve bearings for quiet operation - One piece non-ferrous impeller - Stainless steel shaft - Rugged bronze sleeve bearing - Two piece carbon/ceramic seal assembly - Durable one piece spring coupling - Every circulator is operated before shipment
Resilient mounted, split phase motor with built-in overload protector - Equipped with sleeve bearings for quiet operation - One piece non-ferrous impeller - Stainless steel shaft - Rugged bronze sleeve bearing - Two piece carbon/ceramic seal assembly - Durable one piece spring coupling - Every circulator is operated before shipment
All in one pump and control - Easy to install: Attach 2 included sensors and dial in the desired Delta-T - Snap in replaceable PC board - LED status panel - Fuse protected - Plug in low voltage wiring terminal - Increases system efficiency - Pump always runs at minimum required speed to eliminate velocity noise Eliminates need for a pressure by-pass valve - Conserves energy - Achieves system design goals, even when Installed system varies from original design Pump automatically adjusts to current system conditions - Spend less time figuring out pressure drop (for proper pump sizing) when servicing existing systems. Pump exercise - Delivers Ideal BTU/hr heat transfer for all styles of emitters
All in one pump and control - Easy to install: Attach 2 included sensors and dial in the desired Delta-T - Snap in replaceable PC board - LED status panel - Fuse protected - Plug in low voltage wiring terminal - Increases system efficiency - Pump always runs at minimum required speed to eliminate velocity noise Eliminates need for a pressure by-pass valve - Conserves energy - Achieves system design goals, even when Installed system varies from original design Pump automatically adjusts to current system conditions - Spend less time figuring out pressure drop (for proper pump sizing) when servicing existing systems. Pump exercise - Delivers Ideal BTU/hr heat transfer for all styles of emitters
The Taco 0011 is specifically designed for high head / medium flow applications in large residential or light commercial closed loop hydronic heating and chilled water cooling systems. Ideal for high pressure drop boilers, fan coil units, heat exchangers, large radiant heating and heat recovery/geothermal systems. The unique replaceable cartridge contains all of the moving parts and allows for easy service instead of replacing the entire circulator. Universal flange to flange dimensions and orientation allows the 0011 to easily replace other models. Compact, low power consumption design makes it ideal for high-efficiency jobs
Compact, space saving design - Powerful close-coupled, maintenance free motor - Superior efficiency, high starting torque - Permanently lubricated, sealed for life bearings - Rugged 1/2" Stainless Steel Shaft - Carbon/Silicon-Carbide mechanical seal for long life - Universal flange to flange dimensions; Ideal for retrofits - Anti-Condensate design for chilled water - Dual electrical knock-outs - Dual pressure taps, suction and discharge
Compact, space saving design - Powerful close-coupled, maintenance free motor - Superior efficiency, high starting torque - Permanently lubricated, sealed for life bearings - Rugged 1/2" Stainless Steel Shaft - Carbon/Silicon-Carbide mechanical seal for long life - Universal flange to flange dimensions; Ideal for retrofits - Anti-Condensate design for chilled water - Dual electrical knock-outs - Dual pressure taps, suction and discharge
The Taco 0012 is specifically designed for high flow/medium head applications in large residential and light commercial systems. This circulator can be used on open loop systems and domestic water circulation. The unique replaceable cartridge contains all of the moving parts and allows for easy service instead of replacing the entire circulator. Universal flange to flange dimensions and orientation allows the 0012 to easily replace other models. Compact, low power consumption design makes it ideal for high-efficiency jobs. The 0012-F4 is a direct replacement for the HV Series