For recirculating domestic hot water - ECM permanent magnet motor - Lead free brass housing - AutoAdapt technology - Two temperature sensors - Three operating modes - 100% mode: circulator will run continuously at full speed - Temperature mode: the circulator will keep the water temperature within an automatically detected range - Auto mode: the circulator will learn, store and adapt operating times based on home hot water consumption rates - 6 foot power cord
Circulator Pumps 108
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate and rotor cladding - AutoAdapt proportional pressure control - FlowAdapt and FlowLimit used in systems where a flow limitation is required - Intuitive user interface with TFT display - Constant pressure control - Constant temperature control - Built in differential pressure and temperature sensor - Constant curve duty - Maximum or minimum curve duty - Automatic Night Setback - Internal motor protection - Heat energy meter - Work log history - Insulating shells supplied with single head pumps for heating systems - Large temperature range where the liquid temperature and the ambient temperature are independent of each other
The Taco 008 is designed for a wide range of residential and light commercial higher-head circulating applications. Typical uses include hydronic heating, radiant in-floor/panel heating and closed-loop solar heating systems. The unique replaceable cartridge contains all of the moving parts and allows for easy service, instead of replacing the entire circulator. Compact, direct-drive, low power consumption design is ideal for high-efficiency jobs. Self lubricating - No mechanical seal - Universal flange dimensions
Must be installed with the motor shaft in a horizontal position - A 50% glycol antifreeze solution will reduce the circulator performance by approximately 15% - Two pole PSC motor
Must be installed with the motor shaft in a horizontal position - A 50% glycol antifreeze solution will reduce the circulator performance by approximately 15% - Two pole PSC motor
Must be installed with the motor shaft in a horizontal position - A 50% glycol antifreeze solution will reduce the circulator performance by approximately 15% - Two pole PSC motor
The Taco 008 Stainless Steel circulator can be used in higher-head heat recovery, water source heat pump,open-loop solar heat and domestic water recirculation systems. The unique replaceable cartridge contains all of the moving parts and allows for easy service, instead of replacing the entire circulator. Compact, direct-drive, low power consumption design is ideal for high-efficiency jobs. Self lubricating - No mechanical seal - Universal flange dimensions
The Taco 0010 is designed for a wide range of large residential and light commercial water circulating applications. Typical uses include open loop fresh water systems. The unique replaceable cartridge contains all of the moving parts and allows for easy service, instead of replacing the entire circulator. Compact, direct-drive, low power consumption design is ideal for high-efficiency jobs. Self lubricating - No mechanical seal - Universal flange dimensions
Must be installed with the motor shaft in a horizontal position - A 50% glycol antifreeze solution will reduce the circulator performance by approximately 15% - Two pole PSC motor
The Taco 0012 is specifically designed for high flow/medium head applications in large residential and light commercial systems. Ideal for large BTUH Boilers, 2" recirculation loops, Primary/Secondary loops, commercial water heaters and light commercial heating and cooling systems. The unique replaceable cartridge contains all of the moving parts and allows for easy service instead of replacing the entire circulator. Universal flange to flange dimensions and orientation allows the 0012 to easily replace other models. Compact, low power consumption design makes it ideal for high-efficiency jobs. The 0012-F4 is a direct replacement for the HV Series
The Taco 0014 is specifically designed for medium head/medium flow applications in large residential and light commercial systems. Ideal for large BTUH boilers, primary/secondary loops, commercial water heaters, and light commercial heating and cooling systems. The unique replaceable cartridge contains all of the moving parts and allows for easy service instead of replacing the entire circulator. Universal flange to flange dimensions and orientation allows the 0014 to easily replace other models. The compact, direct-drive, low power consumption design makes it ideal for high-efficiency jobs.
The Taco 008-IFC features a removable integral flow check designed to simplify piping, reduce installation costs and improve system performance. The spring loaded IFC replaces a separate in line flow check. The 008-IFC is designed for a wide range of residential and light commercial higher-head circulating applications. Typical uses include hydronic heating, radiant in-floor/panel heating and closed-loop solar heating systems. The unique replaceable cartridge contains all of the moving parts and allows for easy service, instead of replacing the entire circulator. Compact, direct-drive, low power consumption design is ideal for high-efficiency jobs. Self lubricating - No mechanical seal - Universal flange dimensions
Must be installed with the motor shaft in a horizontal position - A 50% glycol antifreeze solution will reduce the circulator performance by approximately 15% - Two pole PSC motor
The Taco 009 is designed for a wide range of residential and light commercial higher-head / lower-flow water circulating applications. Typical uses include hydronic heating, radiant in-floor/panel heating and closed-loop solar heating systems. It can also be used in higher head/lower flow heat recovery, open loop solar heating, and domestic water recirculating systems. The unique replaceable cartridge contains all of the moving parts and allows for easy service, instead of replacing the entire circulator. Compact, direct-drive, low power consumption design is ideal for high-efficiency jobs. Self lubricating - No mechanical seal - Universal flange dimensions
* 1/12 HP - 1750 RPM - 115V - 1 PHASE - IRON BODY (RED)
2 pole motor - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel rotor can, bearing plate and rotor cladding - Stator housing in aluminum alloy can be turned to change the position of the terminal box - Stator housing has 8 drain holes (that must point downwards) to allow condensed water to escape - Stator with built in thermal overload switch.
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate - Proportional pressure control - Constant pressure control - Constant curve/constant speed - Internal motor protection - Wide temperature range where the liquid temperature and the ambient temperature are independent of each other - LED control indicator
The 0015 3-Speed pump is specifically designed for the wide range of flow and head requirements of today’s hydronic heating systems. It's 3-Speed switching capability provides fine tuning control to match a wide combination of tube diameters and length of runs. The 0015 delivers the highest starting torque in its class and includes a removable, uni-body Integral Flow Check that prevents gravity flow, reduces installation costs and improves pump performance.
The 007e is a variable speed, high-efficiency wet rotor circulator with an ECM permanent magnet motor. Its ECM performance is equivalent to the legendary 007 circulator and is ideal for hydronic systems zoned with circulators or zone valves. Dual electrical knockouts and 6 inch wire leads are included for easy wiring. The 007e is not suitable for chilled water or open loop potable water systems
The Taco 006 is designed for circulating hot or chilled fresh water in open or closed loop applications. Typical uses include hydronic heating, domestic hot water recirculation, hydro-air heating/cooling, heat recovery units, water source heat pumps, drain down open loop Solar systems and potable water applications. The unique, replaceable cartridge contains all of the moving parts and allows for easy service instead of replacing the entire circulator. The compact, low power consumption design is ideal for high efficiency jobs.
The Taco 006 is designed for circulating hot or chilled fresh water in open or closed loop applications. Typical uses include hydronic heating, domestic hot water recirculation, hydro-air heating/cooling, heat recovery units, water source heat pumps, drain down open loop Solar systems and potable water applications. The unique, replaceable cartridge contains all of the moving parts and allows for easy service instead of replacing the entire circulator. The compact, low power consumption design is ideal for high efficiency jobs.
The Taco 0011 is specifically designed for high head / medium flow applications in large residential or light commercial closed loop hydronic heating and chilled water cooling systems. Ideal for high pressure drop boilers, fan coil units, heat exchangers, large radiant heating and heat recovery/geothermal systems. The unique replaceable cartridge contains all of the moving parts and allows for easy service instead of replacing the entire circulator. Universal flange to flange dimensions and orientation allows the 0011 to easily replace other models. Compact, low power consumption design makes it ideal for high-efficiency jobs
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate and rotor cladding - AutoAdapt proportional pressure control - FlowAdapt and FlowLimit used in systems where a flow limitation is required - Intuitive user interface with TFT display - Constant pressure control - Constant temperature control - Built in differential pressure and temperature sensor - Constant curve duty - Maximum or minimum curve duty - Automatic Night Setback - Internal motor protection - Heat energy meter - Work log history - Insulating shells supplied with single head pumps for heating systems - Large temperature range where the liquid temperature and the ambient temperature are independent of each other
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate and rotor cladding - AutoAdapt proportional pressure control - FlowAdapt and FlowLimit used in systems where a flow limitation is required - Intuitive user interface with TFT display - Constant pressure control - Constant temperature control - Built in differential pressure and temperature sensor - Constant curve duty - Maximum or minimum curve duty - Automatic Night Setback - Internal motor protection - Heat energy meter - Work log history - Insulating shells supplied with single head pumps for heating systems - Large temperature range where the liquid temperature and the ambient temperature are independent of each other
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate - Proportional pressure control - Constant pressure control - Constant curve/constant speed - Internal motor protection - Wide temperature range where the liquid temperature and the ambient temperature are independent of each other - LED control indicator
The 0015e3 is a three speed LOW (5 foot head) MEDIUM (10 foot head) HIGH (18 foot head), high-efficiency wet rotor circulator with an ECM permanent magnet motor. Its ECM performance is equivalent to the Taco 0015 3-Speed circulator and is ideal for hydronic systems zoned with circulators or zone valves. Includes BIO Barrier, universal two way flange position and Integral Flow Check. Not suitable for potable water or chilled water systems.
The Taco 007 is a cartridge style, maintenance free, wet-rotor, in-line, single stage circulator pump. It is designed for quiet operation in Hydronic heating, Radiant heating. The unique replaceable cartridge contains all of the moving parts and allows the circulator to be easily serviced instead of replacing the entire unit. Ideal for a wide range of applications.
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate and rotor cladding - AutoAdapt proportional pressure control - FlowAdapt and FlowLimit used in systems where a flow limitation is required - Intuitive user interface with TFT display - Constant pressure control - Constant temperature control - Built in differential pressure and temperature sensor - Constant curve duty - Maximum or minimum curve duty - Automatic Night Setback - Internal motor protection - Heat energy meter - Work log history - Insulating shells supplied with single head pumps for heating systems - Large temperature range where the liquid temperature and the ambient temperature are independent of each other
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate and rotor cladding - AutoAdapt proportional pressure control - FlowAdapt and FlowLimit used in systems where a flow limitation is required - Intuitive user interface with TFT display - Constant pressure control - Constant temperature control - Built in differential pressure and temperature sensor - Constant curve duty - Maximum or minimum curve duty - Automatic Night Setback - Internal motor protection - Heat energy meter - Work log history - Insulating shells supplied with single head pumps for heating systems - Large temperature range where the liquid temperature and the ambient temperature are independent of each other
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate and rotor cladding - AutoAdapt proportional pressure control - FlowAdapt and FlowLimit used in systems where a flow limitation is required - Intuitive user interface with TFT display - Constant pressure control - Constant temperature control - Built in differential pressure and temperature sensor - Constant curve duty - Maximum or minimum curve duty - Automatic Night Setback - Internal motor protection - Heat energy meter - Work log history - Insulating shells supplied with single head pumps for heating systems - Large temperature range where the liquid temperature and the ambient temperature are independent of each other
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate and rotor cladding - AutoAdapt proportional pressure control - FlowAdapt and FlowLimit used in systems where a flow limitation is required - Intuitive user interface with TFT display - Constant pressure control - Constant temperature control - Built in differential pressure and temperature sensor - Constant curve duty - Maximum or minimum curve duty - Automatic Night Setback - Internal motor protection - Heat energy meter - Work log history - Insulating shells supplied with single head pumps for heating systems - Large temperature range where the liquid temperature and the ambient temperature are independent of each other
Compact, space saving design - Powerful close-coupled, maintenance free motor - Superior efficiency, high starting torque - Permanently lubricated, sealed for life bearings - Rugged 1/2" Stainless Steel Shaft - Carbon/Silicon-Carbide mechanical seal for long life - Universal flange to flange dimensions; Ideal for retrofits - Anti-Condensate design for chilled water - Dual electrical knock-outs - Dual pressure taps, suction and discharge
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate and rotor cladding - AutoAdapt proportional pressure control - FlowAdapt and FlowLimit used in systems where a flow limitation is required - Intuitive user interface with TFT display - Constant pressure control - Constant temperature control - Built in differential pressure and temperature sensor - Constant curve duty - Maximum or minimum curve duty - Automatic Night Setback - Internal motor protection - Heat energy meter - Work log history - Insulating shells supplied with single head pumps for heating systems - Large temperature range where the liquid temperature and the ambient temperature are independent of each other
The 00R-IFC Radiant Heating Circulator with Integral Flow Check specifically fits the higher head and lower flow designs used in many Radiant Heating systems. The circulator's performance curve delivers flow that can be used in a wide combination of tube diameters and length of runs. The removable, spring loaded Integral Flow Check prevents gravity flow/reverse flow. By locating the IFC inside the pump casing, a separate in-line flow check is eliminated, simplifying piping and reducing installation costs. It also makes for a modern, clean looking job when mounting the pump in vertical runs of pipe, pumping away from the boiler. Both the IFC and cartridge are easily accessed for service instead of replacing the entire unit.
The Taco 0011 is specifically designed for open loop systems and domestic water circulation.The unique replaceable cartridge contains all of the moving parts and allows for easy service instead of replacing the entire circulator. Universal flange to flange dimensions and orientation allows the 0011 to easily replace other models. Compact, low power consumption design makes it ideal for high-efficiency jobs
Compact, space saving design - Powerful close-coupled, maintenance free motor - Superior efficiency, high starting torque - Permanently lubricated, sealed for life bearings - Rugged 1/2" Stainless Steel Shaft - Carbon/Silicon-Carbide mechanical seal for long life - Universal flange to flange dimensions; Ideal for retrofits - Anti-Condensate design for chilled water - Dual electrical knock-outs - Dual pressure taps, suction and discharge
The 0018e circulator is a variable speed, high-efficiency wet rotor circulator with an ECM permanent magnet motor. Bluetooth capability. Dual electrical knockouts with 6 inch stranded wire leads for easy wiring. Operating modes include infinitely variable fixed speed to fine tune any zone, constant pressure for zone valve applications, proportional pressure for panel radiators with thermostatic radiator valves or self-adjusting activeADAPT auto mode. The 0018e is not suitable for chilled water or open loop potable water systems.
Must be installed with the motor shaft in a horizontal position - A 50% glycol antifreeze solution will reduce the circulator performance by approximately 15% - Two pole PSC motor
The Taco 0011 is specifically designed for high head / medium flow applications in large residential or light commercial closed loop hydronic heating and chilled water cooling systems. Ideal for high pressure drop boilers, fan coil units, heat exchangers, large radiant heating and heat recovery/geothermal systems. The unique replaceable cartridge contains all of the moving parts and allows for easy service instead of replacing the entire circulator. Universal flange to flange dimensions and orientation allows the 0011 to easily replace other models. Compact, low power consumption design makes it ideal for high-efficiency jobs
Internally controlled and are designed for systems with variable flow rates, where the pump is internally controlled via a user interface. Speed control can reduce power consumption considerably. Eight different control modes, including constant pressure, AUTOAdapt and proportional pressure - AUTOAdapt: The AUTOAdapt function continuously adjusts the pump performance to the actual heat demand, i.e. the size of the system and the changing heat demand during the year. The function will find the setting that provides optimal comfort with minimal energy consumption. It contributes to fast, safe and easy commissioning. A magnetite resistant design, robust ceramic shaft, and stainless steel bearing plate ensure that the circulator reliably delivers the optimal system performance throughout the years at the lowest possible energy consumption.