Search results for
All Products
Relevant Product Categories
4 inch diameter pump for use with 4 inch or larger wells - 1-1/4 inch female IPS pump outlet - 16 gallons per minute at 203 foot head - 1 phase - 10 impellers - All stainless steel construction - Sand resistant - Resistant to aggressive water - No electronic communication is possible with this pump - Dry run protection - High efficiency pump and motor
1 inch female IPS connections - 5 foot power cord - 1 phase - Two impellers - Integrated frequency converter - Suitable for water supply in domestic applications. Thanks to the integrated speed controller, the booster keeps a constant pressure in the pipe system. A pressure sensor monitoring changes in the water consumption, will signal to the speed controller to change the motor speed to adapt the performance to the new situation. The optional inlet pressure switch prevents the pump from operating in case of low inlet pressure. The CMBE Booster consists of these components: CME pump with integrated frequency converter, 5 way fitting with non-return valve, diaphragm tank, pressure gauge, and pressure sensor
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate and rotor cladding - AutoAdapt proportional pressure control - FlowAdapt and FlowLimit used in systems where a flow limitation is required - Intuitive user interface with TFT display - Constant pressure control - Constant temperature control - Built in differential pressure and temperature sensor - Constant curve duty - Maximum or minimum curve duty - Automatic Night Setback - Internal motor protection - Heat energy meter - Work log history - Insulating shells supplied with single head pumps for heating systems - Large temperature range where the liquid temperature and the ambient temperature are independent of each other
Fits UP53 and UPS53 series
2-1/2 inch flanged connection (less flanges) - 3 phase - One 4.66 inch impeller - Vertical, multistage centrifugal pump with inlet and outlet ports on same the level. The pump head and base are in cast iron - all other wetted parts are in stainless steel. A cartridge shaft seal ensures high reliability, safe handling, and easy access and service. Power transmission is via a rigid split coupling. The pump is fitted with a 3-phase fan cooled asynchronous motor.
1 inch female IPS connections - 1 phase - Six impellers - Integrated frequency converter - Suitable for water supply in domestic applications. Thanks to the integrated speed controller, the booster keeps a constant pressure in the pipe system. A pressure sensor monitoring changes in the water consumption, will signal to the speed controller to change the motor speed to adapt the performance to the new situation. The optional inlet pressure switch prevents the pump from operating in case of low inlet pressure. The CMBE Booster consists of these components: CME pump with integrated frequency converter, 5 way fitting with non-return valve, diaphragm tank, pressure gauge, and pressure sensor
3 inch diameter pump for use with 3 inch or larger wells - 1 inch female IPS pump outlet - 5 gallons per minute at 180 foot head - 1 phase - Dry run protection - High efficiency pump and motor - Protection against upthrust - Soft start - Over voltage and under voltage protection - Over temperature protection - High starting torque - The following are available if the pump is used with the CU-301 MkII pressure controller: Constant pressure control - Variable speed - Electronic control and communication
2 pole motor - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel rotor can, bearing plate and rotor cladding - Stator housing in aluminum alloy can be turned to change the position of the terminal box - Stator housing has 8 drain holes (that must point downwards) to allow condensed water to escape - Stator with built in thermal overload switch.
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate - Proportional pressure control - Constant pressure control - Constant curve/constant speed - Internal motor protection - Wide temperature range where the liquid temperature and the ambient temperature are independent of each other - LED control indicator
1 inch female IPS connections - 1 phase - Five impellers - Integrated frequency converter - Suitable for water supply in domestic applications. Thanks to the integrated speed controller, the booster keeps a constant pressure in the pipe system. A pressure sensor monitoring changes in the water consumption, will signal to the speed controller to change the motor speed to adapt the performance to the new situation. The optional inlet pressure switch prevents the pump from operating in case of low inlet pressure. The CMBE Booster consists of these components: CME pump with integrated frequency converter, 5 way fitting with non-return valve, diaphragm tank, pressure gauge, and pressure sensor
Single stage, close coupled, volute pump with in line suction and discharge ports of identical diameter. The pump is of the top pull out design, i.e. the power head (motor, pump head and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. Pipework connection is via 150 psi ANSI flanges (not included). The pump is fitted with a fan cooled, permanent magnet synchronous motor. The motor includes a frequency converter and PI controller in the motor terminal box. This enables continuously variable control of the motor speed, which again enables adaptation of the performance to a given requirement. The pump is fitted with a combined temperature and differential pressure sensor.
1 inch feamle IPS connection - 3 phase - Six 3.66 inch impeller - Integrated frequency converter - Vertical, multistage centrifugal pump with inlet and outlet ports on same the level. The pump head and base are in cast iron - all other wetted parts are in stainless steel. A cartridge shaft seal ensures high reliability, safe handling, and easy access and service. Power transmission is via a rigid split coupling. The pump is fitted with a 3-phase fan cooled asynchronous motor.
1 inch female IPS connections - 5 foot power cord - 1 phase - Five impellers - Integrated frequency converter - Suitable for water supply in domestic applications. Thanks to the integrated speed controller, the booster keeps a constant pressure in the pipe system. A pressure sensor monitoring changes in the water consumption, will signal to the speed controller to change the motor speed to adapt the performance to the new situation. The optional inlet pressure switch prevents the pump from operating in case of low inlet pressure. The CMBE Booster consists of these components: CME pump with integrated frequency converter, 5 way fitting with non-return valve, diaphragm tank, pressure gauge, and pressure sensor
2 pole motor - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel rotor can, bearing plate and rotor cladding - Stator housing in aluminum alloy can be turned to change the position of the terminal box - Stator housing has 8 drain holes (that must point downwards) to allow condensed water to escape - Stator with built in thermal overload switch.
Single stage, close coupled, volute pump with in line suction and discharge ports of identical diameter. The pump is of the top pull out design, i.e. the power head (motor, pump head and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. Pipework connection is via 150 psi ANSI flanges (not included). The pump is fitted with a fan cooled, permanent magnet synchronous motor. The motor includes a frequency converter and PI controller in the motor terminal box. This enables continuously variable control of the motor speed, which again enables adaptation of the performance to a given requirement. The pump is fitted with a combined temperature and differential pressure sensor.
2 pole motor - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel rotor can, bearing plate and rotor cladding - Stator housing in aluminum alloy can be turned to change the position of the terminal box - Stator housing has 8 drain holes (that must point downwards) to allow condensed water to escape - Stator with built in thermal overload switch.
3 phase - Flange mount - This pump features a VLS pump, MLE motor and integrated variable frequency drive and control, all made by one supplier. Together with various sensors, these products allow for dynamic and intelligent solutions to many industrial and commercial building applications. The innovative solution cuts planning, purchasing, installation and commissioning costs.The integrated variable frequency motor (MLE) is available with permanent magnet motors and exceeds IE5 efficiency levels set by International Electro Technical Commission, currently the highest efficiency worldwide for electrical motors. NEMA Premium Efficient motors are equivalent to IE3, meaning these MLE motors are two levels above NEMA Premium Efficiency. The combined motor and VFD efficiency is higher than a NEMA Premium motor alone.The VLSC features a VLS pump with a Grundfos CUE variable frequency drive and control
2 pole motor - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel rotor can, bearing plate and rotor cladding - Stator housing in aluminum alloy can be turned to change the position of the terminal box - Stator housing has 8 drain holes (that must point downwards) to allow condensed water to escape - Stator with built in thermal overload switch.
For water - 175 PSI maximum pressure - 150 degrees maximum water temperature - Combines three valves in one: shut off valve, balancing valve, and check valve - Provides the feature of changing the flange orientation to allow 90 degree pipe connection - Reduces the overall system pressure drop since fewer individual components are needed when installing a pump - Simplifies dismantling and servicing - Internal parts, such as the disc, can be easily removed and/or replaced - Contains a built in bypass valve allowing for drainage of water upstream of the check valve. (The bypass valve MUST BE CLOSED at all times in normal operation and should ONLY be used by authorized personnel to drain water from the piping above.)
3 phase - Flange mount - This pump features a VLS pump, MLE motor and integrated variable frequency drive and control, all made by one supplier. Together with various sensors, these products allow for dynamic and intelligent solutions to many industrial and commercial building applications. The innovative solution cuts planning, purchasing, installation and commissioning costs.The integrated variable frequency motor (MLE) is available with permanent magnet motors and exceeds IE5 efficiency levels set by International Electro Technical Commission, currently the highest efficiency worldwide for electrical motors. NEMA Premium Efficient motors are equivalent to IE3, meaning these MLE motors are two levels above NEMA Premium Efficiency. The combined motor and VFD efficiency is higher than a NEMA Premium motor alone.The VLSC features a VLS pump with a Grundfos CUE variable frequency drive and control
Single stage, close coupled, volute pump with in line suction and discharge ports of identical diameter. The pump is of the top pull out design, i.e. the power head (motor, pump head and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. Pipework connection is via 150 psi ANSI flanges (not included). The pump is fitted with a fan cooled, permanent magnet synchronous motor. The motor includes a frequency converter and PI controller in the motor terminal box. This enables continuously variable control of the motor speed, which again enables adaptation of the performance to a given requirement. The pump is fitted with a combined temperature and differential pressure sensor.
2 inch female IPS connection - 1 phase - Two 3.66 inch impeller - Integrated frequency converter - Vertical, multistage centrifugal pump with inlet and outlet ports on same the level. The pump head and base are in cast iron - all other wetted parts are in stainless steel. A cartridge shaft seal ensures high reliability, safe handling, and easy access and service. Power transmission is via a rigid split coupling. The pump is fitted with a 3-phase fan cooled asynchronous motor.
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate and rotor cladding - AutoAdapt proportional pressure control - FlowAdapt and FlowLimit used in systems where a flow limitation is required - Intuitive user interface with TFT display - Constant pressure control - Constant temperature control - Built in differential pressure and temperature sensor - Constant curve duty - Maximum or minimum curve duty - Automatic Night Setback - Internal motor protection - Heat energy meter - Work log history - Insulating shells supplied with single head pumps for heating systems - Large temperature range where the liquid temperature and the ambient temperature are independent of each other
Requires pump control box - 4 inch diameter pump for use with 4 inch or larger wells - 2 inch female IPS pump outlet - 45 gallons per minute at 292 foot head - 3 phase - 12 impellers - All stainless steel construction - Sand resistant - Resistant to aggressive water - No electronic communication is possible with this pump - Dry run protection - High efficiency pump and motor
For water - 175 PSI maximum pressure - 150 degrees maximum water temperature - Provides a uniform flow pattern to the suction side of the pump - Incorporates a cylindrical strainer preventing impurities from entering the pump. Comes with a disposable, fine mesh, stainless steel start up screen for capture and removal of foreign particulates in system piping. - Provides flexibility through an adjustable support for mounting. - Simplifies dismantling and servicing. - Internal parts, such as strainer, can be easily removed, cleaned, and or replaced.
DN 50 flanged connection (less flanges) - 3 phase - Two 4.13 inch impeller - Integrated frequency converter - Vertical, multistage centrifugal pump with inlet and outlet ports on same the level. The pump head and base are in cast iron - all other wetted parts are in stainless steel. A cartridge shaft seal ensures high reliability, safe handling, and easy access and service. Power transmission is via a rigid split coupling. The pump is fitted with a 3-phase fan cooled asynchronous motor.
3 inch diameter pump for use with 3 inch or larger wells - 1-1/4 inch female IPS pump outlet - 15 gallons per minute at 180 foot head - 1 phase - Dry run protection - High efficiency pump and motor - Protection against upthrust - Soft start - Over voltage and under voltage protection - Over temperature protection - High starting torque - The following are available if the pump is used with the CU-301 MkII pressure controller: Constant pressure control - Variable speed - Electronic control and communication
