Must be installed with the motor shaft in a horizontal position - A 50% glycol antifreeze solution will reduce the circulator performance by approximately 15% - Two pole PSC motor
Search results for
All Products
376
products found manufactured by Grundfos
Relevant Product Categories
Fits UP15, UPS15, UP26, and UPS26
2 pole motor - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel rotor can, bearing plate and rotor cladding - Stator housing in aluminum alloy can be turned to change the position of the terminal box - Stator housing has 8 drain holes (that must point downwards) to allow condensed water to escape - Stator with built in thermal overload switch.
2 inch female IPS connection (less flanges) - 3 phase - Two 4.66 inch impeller - Integrated frequency converter - Vertical, multistage centrifugal pump with inlet and outlet ports on same the level. The pump head and base are in cast iron - all other wetted parts are in stainless steel. A cartridge shaft seal ensures high reliability, safe handling, and easy access and service. Power transmission is via a rigid split coupling. The pump is fitted with a 3-phase fan cooled asynchronous motor.
The CIM-300 has terminals for the BACnet MS/TP connection. DIP switches are used to set transmission speed and line termination and to select the custom Device Object Instance Number. Two hexadecimal rotary switches are used to set the BACnet address. Two LEDs are used to indicate the actual status of the CIM-300 communication. One LED is used for indication of correct connection to the pump, and the other is used to indicate BACnet communication status.
1 inch female IPS connections - 1 phase - Seven impellers - Integrated frequency converter - Suitable for water supply in domestic applications. Thanks to the integrated speed controller, the booster keeps a constant pressure in the pipe system. A pressure sensor monitoring changes in the water consumption, will signal to the speed controller to change the motor speed to adapt the performance to the new situation. The optional inlet pressure switch prevents the pump from operating in case of low inlet pressure. The CMBE Booster consists of these components: CME pump with integrated frequency converter, 5 way fitting with non-return valve, diaphragm tank, pressure gauge, and pressure sensor
For water - 175 PSI maximum pressure - 150 degrees maximum water temperature - Combines three valves in one: shut off valve, balancing valve, and check valve - Provides the feature of changing the flange orientation to allow 90 degree pipe connection - Reduces the overall system pressure drop since fewer individual components are needed when installing a pump - Simplifies dismantling and servicing - Internal parts, such as the disc, can be easily removed and/or replaced - Contains a built in bypass valve allowing for drainage of water upstream of the check valve. (The bypass valve MUST BE CLOSED at all times in normal operation and should ONLY be used by authorized personnel to drain water from the piping above.)
2 pole motor - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel rotor can, bearing plate and rotor cladding - Stator housing in aluminum alloy can be turned to change the position of the terminal box - Stator housing has 8 drain holes (that must point downwards) to allow condensed water to escape - Stator with built in thermal overload switch.
2 pole motor - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel rotor can, bearing plate and rotor cladding - Stator housing in aluminum alloy can be turned to change the position of the terminal box - Stator housing has 8 drain holes (that must point downwards) to allow condensed water to escape - Stator with built in thermal overload switch.
3 inch flanged connection (less flanges) - 3 phase - One 5-3/4 inch impeller - Integrated frequency converter - Vertical, multistage centrifugal pump with inlet and outlet ports on same the level. The pump head and base are in cast iron - all other wetted parts are in stainless steel. A cartridge shaft seal ensures high reliability, safe handling, and easy access and service. Power transmission is via a rigid split coupling. The pump is fitted with a 3-phase fan cooled asynchronous motor.
4 pole motor- Double head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate and rotor cladding - AutoAdapt proportional pressure control - FlowAdapt and FlowLimit used in systems where a flow limitation is required - Intuitive user interface with TFT display - Constant pressure control - Constant temperature control - Built in differential pressure and temperature sensor - Constant curve duty - Maximum or minimum curve duty - Automatic Night Setback - Internal motor protection - Heat energy meter - Work log history - Insulating shells supplied with single head pumps for heating systems - Large temperature range where the liquid temperature and the ambient temperature are independent of each other
2 pole motor - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel rotor can, bearing plate and rotor cladding - Stator housing in aluminum alloy can be turned to change the position of the terminal box - Stator housing has 8 drain holes (that must point downwards) to allow condensed water to escape - Stator with built in thermal overload switch.
1-1/4 inch female IPS inlet connections - 1 inch female IPS outlet connection - 1 phase - Four impellers - Integrated frequency converter - Suitable for water supply in domestic applications. Thanks to the integrated speed controller, the booster keeps a constant pressure in the pipe system. A pressure sensor monitoring changes in the water consumption, will signal to the speed controller to change the motor speed to adapt the performance to the new situation. The optional inlet pressure switch prevents the pump from operating in case of low inlet pressure. The CMBE Booster consists of these components: CME pump with integrated frequency converter, 5 way fitting with non-return valve, diaphragm tank, pressure gauge, and pressure sensor
Includes pressure switch - Stainless steel pump housing - 6.50 gallons per minute at 105 foot head - 154 foot maximum head - 1 phase - 1 inch female IPS inlet - 1 inch female IPS outlet - Self priming, single stage centrifugal pumps that feature an axial suction port and a radial discharge port. The pumps have a built in ejector with guide vanes for optimum self priming properties. Stable operation even if there is air in the liquid - Robust design that makes the pump suitable for fixed installation - The pump is directly coupled to a special fan cooled asynchronous Grundfos motor that is adapted to the pump performance
2 pole motor - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel rotor can, bearing plate and rotor cladding - Stator housing in aluminum alloy can be turned to change the position of the terminal box - Stator housing has 8 drain holes (that must point downwards) to allow condensed water to escape - Stator with built in thermal overload switch.
Three constant pressure settings - Must be installed with the motor shaft in a horizontal position - A 50% glycol antifreeze solution will reduce the circulator performance by approximately 15%
Three constant pressure settings - Must be installed with the motor shaft in a horizontal position - A 50% glycol antifreeze solution will reduce the circulator performance by approximately 15%
AutoAdapt technology - Two temperature sensors - Three operating modes - 100% mode: circulator will run continuously at full speed - Constant pressure: the circulator will keep the water pressure constant - Auto mode: the circulator will learn, store and adapt operating times based on home hot water consumption rates - Must be installed with the motor shaft in a horizontal position - A 50% glycol antifreeze solution will reduce the circulator performance by approximately 15%
AutoAdapt technology - Two temperature sensors - Three operating modes - 100% mode: circulator will run continuously at full speed - Constant pressure: the circulator will keep the water pressure constant - Auto mode: the circulator will learn, store and adapt operating times based on home hot water consumption rates - Must be installed with the motor shaft in a horizontal position - A 50% glycol antifreeze solution will reduce the circulator performance by approximately 15%
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate - Proportional pressure control - Constant pressure control - Constant curve/constant speed - Internal motor protection - Wide temperature range where the liquid temperature and the ambient temperature are independent of each other - LED control indicator
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate - Proportional pressure control - Constant pressure control - Constant curve/constant speed - Internal motor protection - Wide temperature range where the liquid temperature and the ambient temperature are independent of each other - LED control indicator
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate - Proportional pressure control - Constant pressure control - Constant curve/constant speed - Internal motor protection - Wide temperature range where the liquid temperature and the ambient temperature are independent of each other - LED control indicator
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate - Proportional pressure control - Constant pressure control - Constant curve/constant speed - Internal motor protection - Wide temperature range where the liquid temperature and the ambient temperature are independent of each other - LED control indicator
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate - Proportional pressure control - Constant pressure control - Constant curve/constant speed - Internal motor protection - Wide temperature range where the liquid temperature and the ambient temperature are independent of each other - LED control indicator
4 pole motor- Single head circulator - Pumps are of the canned rotor type, meaning that the pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. - Stainless steel bearing plate - Proportional pressure control - Constant pressure control - Constant curve/constant speed - Internal motor protection - Wide temperature range where the liquid temperature and the ambient temperature are independent of each other - LED control indicator
The UPZC series of zone controls is the ideal choice for single and multiple zone hydronic heating systems when you are using zone valves. All multiple zone controls are expandable to handle any size of job. Boiler pumps, domestic hot water pumps and system pump, as well as assigning priority can be controlled from a the UPZC control. The side mounted terminals provide easy access and ease in wiring and the front facing, easy to read LED indicators on the front panel provide essential operation status.
The UPZC series of zone controls is the ideal choice for single and multiple zone hydronic heating systems when you are using zone valves. All multiple zone controls are expandable to handle any size of job. Boiler pumps, domestic hot water pumps and system pump, as well as assigning priority can be controlled from a the UPZC control. The side mounted terminals provide easy access and ease in wiring and the front facing, easy to read LED indicators on the front panel provide essential operation status.
The UPZC series of zone controls is the ideal choice for single and multiple zone hydronic heating systems when you are using zone valves. All multiple zone controls are expandable to handle any size of job. Boiler pumps, domestic hot water pumps and system pump, as well as assigning priority can be controlled from a the UPZC control. The side mounted terminals provide easy access and ease in wiring and the front facing, easy to read LED indicators on the front panel provide essential operation status.
The UPZC series of zone controls is the ideal choice for single and multiple zone hydronic heating systems when you are using zone pumps. All multiple zone controls are expandable to handle any size of job. Boiler pumps, domestic hot water pumps and system pump, as well as assigning priority can be controlled from a the UPZC control. The side mounted terminals provide easy access and ease in wiring and the front facing, easy to read LED indicators on the front panel provide essential operation status.
The UPZC series of zone controls is the ideal choice for single and multiple zone hydronic heating systems when you are using zone pumps. All multiple zone controls are expandable to handle any size of job. Boiler pumps, domestic hot water pumps and system pump, as well as assigning priority can be controlled from a the UPZC control. The side mounted terminals provide easy access and ease in wiring and the front facing, easy to read LED indicators on the front panel provide essential operation status.
4 inch diameter pump for use with 4 inch or larger wells - 1 inch female IPS pump outlet - 7 gallons per minute at 361 foot head - 1 phase - 19 impellers - All stainless steel construction - Sand resistant - Resistant to aggressive water - No electronic communication is possible with this pump - Dry run protection - High efficiency pump and motor
4 inch diameter pump for use with 4 inch or larger wells - 1 inch female IPS pump outlet - 7 gallons per minute at 151 foot head - 1 phase - 8 impellers - All stainless steel construction - Sand resistant - Resistant to aggressive water - No electronic communication is possible with this pump - Dry run protection - High efficiency pump and motor
Includes 6-1/2 foot power cord - 1 phase - This is a fully integrated, self-priming, compact pump for pressure boosting in domestic applications. SCALA2 incorporates integrated speed control enabling the keeping of the perfect pressure at the taps, meaning that the pump performance will increase with increasing demand. SCALA2 can be installed in three easy steps: 1. Connect the pipes. 2. Prime the pump. 3. Plug the pump into the power outlet and the pump will start. Grundfos SCALA2 has all the components necessary to ensure a comfortable pressure: intelligent controller, integrated speed-controlled drive, integrated tank integrated sensors, and integrated non return valves. As it is self priming, the SCALA2 is able to pump water from a level below the pump. Provided it is filled with water, the pump is able to lift water from a depth of 8 m in less than 5 minutes. This facilitates easy installation and start up of the pump and provides more reliable water supply in installations where there is a risk of dry running and leakages in suction hose or pipes. If exposed to dry running, water shortage or excessive temperature, blocked pump, or in case of seizure or overload, the pump will stop automatically, thus preventing a motor burnout. The pump features an automatic reset function. Restarting will be attempted every 5 minutes 8 times, thereafter new restart attemps will occur every 24 hours. The automatic reset function can be deactivated. Thanks to its hydraulic design, permanent magnet motor and water cooling, the pump is extremely low-noise, and is suitable for indoor or outdoor use. The built in pressure tank reduces the number of starts and stops in case of leakages in the pipe system, causing less wear on the pump. SCALA2 requires no maintainance, but it is recommended to keep the pump clean, check the non return valves and keeping the ventilation holes free of dust
1 phase - This is a fully integrated, self-priming, compact pump for pressure boosting in domestic applications. SCALA2 incorporates integrated speed control enabling the keeping of the perfect pressure at the taps, meaning that the pump performance will increase with increasing demand. SCALA2 can be installed in three easy steps: 1. Connect the pipes. 2. Prime the pump. 3. Plug the pump into the power outlet and the pump will start. Grundfos SCALA2 has all the components necessary to ensure a comfortable pressure: intelligent controller, integrated speed-controlled drive, integrated tank integrated sensors, and integrated non return valves. As it is self priming, the SCALA2 is able to pump water from a level below the pump. Provided it is filled with water, the pump is able to lift water from a depth of 8 m in less than 5 minutes. This facilitates easy installation and start up of the pump and provides more reliable water supply in installations where there is a risk of dry running and leakages in suction hose or pipes. If exposed to dry running, water shortage or excessive temperature, blocked pump, or in case of seizure or overload, the pump will stop automatically, thus preventing a motor burnout. The pump features an automatic reset function. Restarting will be attempted every 5 minutes 8 times, thereafter new restart attemps will occur every 24 hours. The automatic reset function can be deactivated. Thanks to its hydraulic design, permanent magnet motor and water cooling, the pump is extremely low-noise, and is suitable for indoor or outdoor use. The built in pressure tank reduces the number of starts and stops in case of leakages in the pipe system, causing less wear on the pump. SCALA2 requires no maintainance, but it is recommended to keep the pump clean, check the non return valves and keeping the ventilation holes free of dust
3 inch diameter pump for use with 3 inch or larger wells - 1-1/4 inch female IPS pump outlet - 10 gallons per minute at 160 foot head - 1 phase - No electronic communication is possible with this pump - Dry run protection - High efficiency pump and motor - Protection against upthrust - Soft start - Over voltage and under voltage protection - Over temperature protection - High starting torque
3 inch diameter pump for use with 3 inch or larger wells - 1-1/4 inch female IPS pump outlet - 10 gallons per minute at 240 foot head - 1 phase - Dry run protection - High efficiency pump and motor - Protection against upthrust - Soft start - Over voltage and under voltage protection - Over temperature protection - High starting torque - Electronic control is not possible with this pump
3 inch diameter pump for use with 3 inch or larger wells - 1 inch female IPS pump outlet - 5 gallons per minute at 270 foot head - 1 phase - Dry run protection - High efficiency pump and motor - Protection against upthrust - Soft start - Over voltage and under voltage protection - Over temperature protection - High starting torque - The following are available if the pump is used with the CU-301 MkII pressure controller: Constant pressure control - Variable speed - Electronic control and communication
3 inch diameter pump for use with 3 inch or larger wells - 1 inch female IPS pump outlet - 5 gallons per minute at 410 foot head - 1 phase - No electronic communication is possible with this pump - Dry run protection - High efficiency pump and motor - Protection against upthrust - Soft start - Over voltage and under voltage protection - Over temperature protection - High starting torque
3 inch diameter pump for use with 3 inch or larger wells - 1 inch female IPS pump outlet - 5 gallons per minute at 320 foot head - 1 phase - No electronic communication is possible with this pump - Dry run protection - High efficiency pump and motor - Protection against upthrust - Soft start - Over voltage and under voltage protection - Over temperature protection - High starting torque
4 inch diameter pump for use with 4 inch or larger wells - 1-1/4 inch female IPS pump outlet - 16 gallons per minute at 102 foot head - 1 phase - 5 impellers - All stainless steel construction - Sand resistant - Resistant to aggressive water - No electronic communication is possible with this pump - Dry run protection - High efficiency pump and motor
Fits MS series motors - 1 phase - Heavy duty epoxy coated steel box with internal protective shields and a pull handle quick disconnect
Fits CU-301 - 65.6 foot long cable - 2 wire - 119.95 PSI maximum measuring pressure
3 inch diameter pump for use with 3 inch or larger wells - 1-1/4 inch female IPS pump outlet - 15 gallons per minute at 110 foot head - 1 phase - Dry run protection - High efficiency pump and motor - Protection against upthrust - Soft start - Over voltage and under voltage protection - Over temperature protection - High starting torque - The following are available if the pump is used with the CU-301 MkII pressure controller: Constant pressure control - Variable speed - Electronic control and communication
Includes pressure switch - 6.50 gallons per minute at 120 foot head - 177 foot maximum head - 1 phase - 1-1/4 inch female IPS inlet - 1 inch female IPS outlet - Self priming, single stage centrifugal pumps that feature an axial suction port and a radial discharge port. The pumps have a built in ejector with guide vanes for optimum self priming properties. Stable operation even if there is air in the liquid - Robust design that makes the pump suitable for fixed installation - The pump is directly coupled to a special fan cooled asynchronous Grundfos motor that is adapted to the pump performance
Fits UP series circulators - Fits 1/2 inch copper tubing - 85 to 105 degree temperature range - 14 inches long - Two 18 gauge conductors