The SumpJet® (Model SJ10) is a water powered back-up sump pump that will protect your basement in the case of a power outage. This unique product is powered by your municipal water supply and requires no electricity to operate with a compact high efficiency design, The SumpJet® removes 2 gal of sump water per 1 gal used. The SumpJet® is fully automatic, arrives completely assembled and comes backed with Liberty's standard 3 year warranty.
Liberty Pumps®, SJ10, 16 gpm Flow Rate, 3/4 in NPT Inlet, 1-1/2 in Outlet, 15 ft Maximum Head, 100 psi Maximum, 130 deg F, ABS, 4.8 in D x 20.9 in H Dimensions
Sump Pumps 15
Features
- Heavy-duty cast iron construction
- Permanent split capacitor (PSC) motor with thermal overload protection
- Designed for continuous duty
- Energy-saving low amp draw
- Cooler running motor
- 1-1/2" FNPT discharge (38 mm)
- Handles up to 1/2" (12.7 mm) solids
- Multiple switch options for automatic operation
- 140 Degrees F (60 Degrees C) liquid temperature rating
- cCSAus listed
Overview
Features
- Float-operated, submersible, 2-pole mechanical switch integrating advanced switch technology
- Corrosion-resistant, powder coated epoxy finish
- All cast iron construction
- Viton outer switch boot
- No sheet metal parts to rust or corrode
- Stainless steel screws, switch arm, guard and handle
- No screens to clog
- Watertight, neoprene square ring between motor and pump housing
- Solid, buoyant, polypropylene float
- Oil-filled, hermetically-sealed, automatic reset thermal overload protected motor
- Upper and lower sleeve bearings running in bath of oil
- Entire unit pressure-tested after assembly
- Carbon and ceramic shaft seal
- Maximum temperature for effluent or dewatering: 130 Degrees F (54 Degrees C)
- Passes 1/2" (12 mm) spherical solids
- 1-1/2" NPT discharge
- On point: 7-1/4" (18 cm)
- Off point: 3" (8 cm)
- Major width: 10-3/32" (26.2 cm)
- Major height: 10-1/16" (25.6 cm)
- Watertight and dust-tight
- Permanently oiled bearings
- Cast iron impeller
- 5 year limited warranty
Overview
This "Flow-Mate" model submersible pump is designed for use in residential or light commerical dewatering applications and can be used to transfer groundwater or effluent. This durable cast iron pump includes a powder coated epoxy finish to prevent corrosion and is designed to provide great heat dissipation from the motor, ensuring a long service life. As with every Zoeller pump, each one is 100% pressure-tested, submerged and run to ensure quality and reliability for years of trouble-free performance! This attention to detail is an inherent feature of every pump, making it one of the most reliable in the industry.
- Corrosion-resistant, powder-coated epoxy finish
- Durable, cast iron construction
- Cast iron switch case, motor, pump housing and base
- No sheet metal parts to rust or corrode
- All castings are cast iron class 25-30 25000# tensile strength
- Stainless steel screws, guard, handle, arm and seal assembly
- Float-operated 2-pole mechanical switch
- Permanent split capacitor motor, oil-filled and hermetically-sealed, automatic reset thermal overload protection
- Bearings - upper and lower oil-fed cast iron
- Carbon and ceramic shaft seal
- Entire unit pressure-tested after assembly
- Watertight, neoprene square ring between motor and pump housing
- Maximum termperature for effluent or dewatering: 130 Degrees F (54 Degrees C)
- Passes 1/2" (13 mm) spherical solids
- No screens to clog
- 1-1/2" NPT discharge (1-1/2" x 2" PVC adapter included with BN and BE models)
- On point: 9-1/2" (24 cm)
- Off point: 3" (8 cm)
- Major width: 10" (25.7 cm)
- Major height: 12" (30 cm)
- Simplex and duplex systems available
- Packaged systems available
- Automatic and non-automatic available
- Available with piggyback variable level float switch
The Top Choice for basement sumps, the 3/10 HP Model M53 automatic Sump Pump is designed to remove groundwater from basement sump applications. The pump comes standard with the Zoeller LED Plug that allows you to check for power at a quick glance. Backed by a 3-year warranty, this corrosion resistant pump will provide the dependability expected from a Zoeller pump. Every pump is submerged in water and tested to its published performance curve, ensuring it meets your expectations and delivers peace of mind right out of the box.
Zoeller® Effluent/Dewatering Submersible Pump, Automatic, Series: Mighty-Mate M53, 43 gpm, 1-1/2 in Outlet, 19-1/4 ft Maximum Head, 3/10 hp, 115 V AC, 9.7 A, 60 Hz Frequency, 1 ph, 1550 rpm Motor, 3-Wire Cord, Non-Clogging Vortex Impeller, 130 deg F, Sleeve Bearing, Cast Iron, 10.0625 in H x 10.06 in W Dimensions
The 3/10 HP Crawl Space System eliminates water and dampness in tight or restricted areas that has pooling water or poor drainage. Add-on service for pest control operators, water-proofers, remodelers, structural repair services, and contractors.
Zoeller® Crawl Space® Pumping System, 19 to 43 gpm, 19-1/4 ft Maximum Head, 1/3 hp, 115 V AC, 9.7 A, 60 Hz Frequency, 1 ph ph, 3-Wire Cord, Non-Clogging Vortex Impeller, 130 deg F, Cast Iron, 14-7/8 in H x 12-1/4 in W Dimensions
Rugged and dependable heavy duty cast iron pump with powder coat finish. Liberty's "workhorse" sump pump features a unique one-piece cast iron body, quick-disconnect power cord and three different switch options - including our vertical magnetic float design (VMF) for smaller pits (model 257). With a durable, epoxy powder coat finish and vortex style impeller, Liberty's 250 series pump is the perfect choice for low-head effluent pumping or basement de-watering.
Liberty Pumps®, 257, Low-Head, Series: 250, 45 gpm Maximum, 5 ft Rated Head, Automatic/Non Automatic: Automatic, 1-1/2 in Outlet, 23 ft Maximum Head, 1/3 hp, 115 V AC, 5.2 A Full Load/8 A Locked Rotor, 60 Hz Frequency, 1 ph, 3450 rpm Motor, SJTW 10 ft Cord, Engineered Polymer Vortex Impeller, 221 deg F Thermal Overload, NEMA 1/4X Enclosure, Ball/Race Bearing, Cast Iron, 9.6 in W x 10.5 in H Dimensions
* SUBMERSIBLE - 46 GPM AT 5' - 115 VOLTS - 25' CORD
SHUTS OFF AT 18 FEET
The 1/2 HP Model M137 automatic Sump Pump is designed to remove groundwater from basement sump applications. This corrosion resistant pump will provide the dependability expected from a Zoeller pump. Backed by a 3-year warranty, every pump is submerged in water and tested to its published performance curve, ensuring it meets your expectations and delivers peace of mind right-out-of-the-box.
Zoeller®, 137-0001, Effluent Pump, 10' Cord Length, Series: M137 Flow-Mate, 93 gpm Maximum, Automatic/Non Automatic: Automatic, 1-1/2 in NPT Outlet, 26 ft Maximum Head, 1/2 hp, 115 V, 10.7 A, 60 Hz Frequency, 1 ph, 1725 rpm Motor, 3-Wire Neoprene Cord, Non-Clogging Vortex Impeller, 130 deg F, Sleeve Upper/Sleeve Lower Bearing, Cast Iron, Domestic
Features and Benefits
- For clear water, emergency backup usage when power is off or the primary pump(s) fail
- Extra protection when the primary AC pump fails due to power outages in storms, brownouts, wiring or electrical problems, when the primary pump fails due to damage, mechanical malfunction or obstructions in the pit, or when the primary pump fails to keep up with excessive water due to rain or overloading
- No other system offers the reliability and protection provided by the Basement Sentry(R)
- Battery not included
The 1/6 HP Model 42 Utility Pump is a nonautomatic pump designed to remove unwanted water from almost any surface where it may collect. It can be fully submerged in water. It will pump the water level down to within 1/8" (3 mm) of a flat surface. The Model 42 is an ideal pump for removing water from swimming pools, hot tubs, pool covers, basements, crawl spaces, water troughs, rain barrels, and more. A lightweight and portable performer.
Zoeller®, 42-0008, Utility Pump, Series: Model 42, 15 gpm Flow Rate, 1 in NPT Outlet, 19 ft Maximum Head, 115 V, 1.5 A, 1 ph, 1/6 hp, Polypropylene, UV protected
Our indoor simplex 18" x 30" polyethylene basin with a steel cover is an essential component to the pump system that collects water or wastewater. This type of basin can be used indoors in a residential or light commercial building using a submersible effluent or sewage pump.
Zoeller®, 31-0615, Pump Basin, Simplex, 18 in Width, 30 in Height, Polyethylene
The 0.30 HP Model M53 Sump Pump with a 25' cord is designed to remove groundwater from basement sump applications. This corrosion resistant pump will provide the dependability expected from a Zoeller pump. Backed by a 3-year warranty, every pump is submerged in water and tested to its published performance curve, ensuring it meets your expectations and delivers peace of mind right out of the box.
Zoeller® Submersible Pump, Single Seal Automatic, Series: Mighty-Mate 50, 43 gpm, 1-1/2 in NPT Outlet, 19-1/4 ft Maximum Head, 3/10 hp, 115 V AC, 9.7 A, 60 Hz Frequency, 1 ph ph, 1550 rpm Motor, 3-Wire Cord, Non-Clogging Vortex Impeller, 130 deg F, Sleeve Bearing, Cast Iron, 10-3/32 in W x 10-1/16 in H Dimensions